Jump to content

robert.davis

Members
  • Posts

    36
  • Joined

  • Last visited

About robert.davis

  • Birthday 11/24/2001

Profile Information

  • Gender
    Male
  • Location
    hesperia california
  • Cars
    '86 720 kingcab

Recent Profile Visitors

1,192 profile views

robert.davis's Achievements

Newbie

Newbie (1/14)

  • Conversation Starter Rare
  • Week One Done
  • One Month Later Rare
  • One Year In Rare

Recent Badges

38

Reputation

  1. robert.davis

    Power windows

    I picked up some power windows at the junky yard while already knowing that they wouldnt fit in my doors, (i have rollup windows and am trying to go to factory power) im assuming maybe someone has done this or may have advice from working on power window regulators what needs to get cut out or moved in order to install the new motors. Also does anyone have the piece that mounts to the door panel (i have the switches just need the piece the switches sit on) thank you any info help!
  2. The motor rebuilder jacked up my rods and i need news cant find them anywhere does anyone know where i can get a new set are the ka24 and z24 the same? Heard the blocks are the same just the headed were diffrent in which case could i use hardbody/d21 rods? Need them semi- quick
  3. I seen this one but the recommended is 75-90 i wanted to bump up to 80-90 bc i figure with 250k miles my tranny probably pretty worn, you dont think 85 would be too much
  4. robert.davis

    Tranny fluid

    I think i fixed my leak but im in another pickle. I cant find fluid i seen on another thread that i need gl4 fluid i cant seem to find any 75w-90 or 80w-90 that is gl4 everything i find is gl-5 i see one that says its suitable for nonsynchro manuel trans requireing gl4 any advice on that??
  5. robert.davis

    Tranny leak

    I seam to have a leak at my transmission and right now i was swapping out my carrier bearing on the driveshaft and figured id check out the leak and i thought it might be the seal going from end of the transmission to the drive shaft. I thought it would be metal but its a rubber seal... it spins. Is that a bad sign and should i replace it or is it meant to spin with the driveline and if so any other ideas on where the leak could be bc i cant really seem to tell i thought it could be from wherever the shifter is at(whatever that part is called excuse my ignored) it seems to have a lot if oil around there but i figured id probably see it on the inside of the cab as well on my shifter boot
  6. problem with bagging the truck is you will still need the blocks. i am running four inches in the rear and the bag sits on top of the diff to the frame in order to get low with the bags they blocks will need to keep the gap small when your aired out. with four inch blocks.... its tight down there from the bottom of the leaf spring to the floor its about 2 inches... maybe. but its also still sitff so if you want to go lower you will need to take a leaf out or go 5 inches... or somehow incorporate weight to the back of the truck along with cutting the bump stop... but you said you notched it so you should be alright
  7. as for the middle of the of the seat they did make center consoles with an arm rest that may be able to fit but im not to sure about it
  8. long one piece lights came off of the nissan maximas super hard to find super rare super expensive lol yet to have heard of another one piece head light that fit but i may be mistaken
  9. learned something when doing mine, low beam to high beam doesn't change positive is adds another ground. so to have my leds wired up correctly i would have to add relays and change the grounds into positives and then wire using the harnesses. kind of a pain
  10. you are right the 85 is the automatic and my 86 is stick shift. thanks for the info. i have some decisions to make lol. im already running smaller than stock tires so i have lost a lot of top end speed dont want to loose much more lol
  11. ahh ok i checked that earlier one is 38 and one is 37 both 2wd though the first 7 numbers/ are different on both aswell though will that affect it ?
  12. on ebay "rubber done right" i believe is there name have the seals they have seals with and without the chrome trim as for the windshield itself i found a guy on offer up but he wants like 250 for the glass not installed no seal. i went to my local windshield place and they said they had the glass and would install with "universal seal" for 130 not sure how much i trust that uni seal tho i told the guy i wanted the chrome trim seal and i would provide it for him he said it would run me 170 for the glass and installation with the chrome trim. i think you could find a windshield guy near you and they would probably have all of those options
  13. I have my truck which is an 86 kingcab and i also have a donor parts truck which is an 85 single cab, however it is a long bed so the chassis is the same. just wondering if the rear ends can get swapped mine took a dump a few days ago and rather then taking the axles out and pull the third piece out and trying to diagnose the problem i figured i just switch rear ends mine had water in the oil and a bunch of metal shavings the donor truck oil looked practically brand new and there wasn't any piece of metal just normal shaving from wear on the magnet. overall looks much better. the donor parts truck is also an automatic not sure if that will make a difference in the gearing. can anyone confirm any of this? can i just swap the rear end or am i making a big NO-NO
  14. I picked up a new window for my kingcab because ive always wanted a slider but i picked it up and the latch seems to be broken. i cant seem to find any online and they seem that they dont make that part...so i thought, im pretty sure i may be able to use a nissan hardbody/d21 sliding rear window latch they look extremely similar but i have never tired swapping them... can anyone confirm my theory will the latch and backing plates work because id like to get all new hardware not just the latch.
  15. will it do that ?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.