Jump to content

ViperGT

Members
  • Posts

    93
  • Joined

  • Last visited

Profile Information

  • Gender
    Not Telling
  • Location
    Long Beach California
  • Interests
    Shifter karting

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

ViperGT's Achievements

Newbie

Newbie (1/14)

-2

Reputation

  1. Hahah fast forward 8 years or how ever long it’s been. Built motor has got about 40k miles on it. Makes about 400 wheel on E85. Kept breaking transmissions, z33 trans swap is all done except driveshaft and tunnel. Running a gtx3076 on 15 psi or so, OS twin plate ev14 1000cc’s that are about maxed out. Aem V2, infinity waiting to go in. Long nose r200 Nismo gt lsd. 280zx halfshafts. car has had a couple small accidents, had to replace windshield with Lexan. Roll cage Being made up over the next couple months. Mess of wiring at the moment.
  2. Got exhaust side springs on and all valve guide seals, the seals were definatley a learning experience ruined one and messed up the spring on another so I had to get a new set.
  3. looking at aem but also considering MS. I will be rocking the stockers until they break again. already gone through 2 N/A lol, and i didnt break any after i welded my diff. Also have an open R200 that im gonna swap in welded most likely just cant fork out that extra 1000 for a r200 lsd, and i didnt have any understear probelms with a welded diff but i also have no front sway bar at the moment.
  4. well im stuck between a gt30,32 and 35 id like to hit 650 on RACE gas but then again until i do serious body work i wont have traction, so maybe for now i just go with gt30 or 32 and leave it at 450-550 at max boost pump gas
  5. yeah i know haha, but it will be worth it if i can make it clean. more pics head work done...
  6. im in long beach and im pretty good, i have wired up and swapped 2 ka's into a 510 and a 620. If somehow your ever in long beach or close id definitely come help for cheap!
  7. here it is, this is tons of work but there are some ideas/ shortcuts that can be taken from it! http://www.vipstylecars.com/forums/showthread.php?2726-DIY-WIDE-BODY-Ya-betta-aks-somebody
  8. long time no update. got a build ka now in the works just got porting on head done. valve job should be done when i get my mis-matched intake valves from supertech. been cutting out rust here and there no patches yet tho lol just holes. got rear coilovers w/225s WAY to soft, hits bump stops under power around corners and then slides. Painted rear seat area/floor and trunk white, looks very good also installing new fuel pump. Roadster has been daily for a while, will be in for paint when 510 is running. Bad blinker issues, fuse pops as soon as i turn on the key, also blinker wiring under dash looks like its been played with pretty hard. PICS!!! possibly looking at something like this to fit slicks... removable front core support, very handy still have grinding and painting to do but i like it. still need FUNCTIONAL hood pins. dont hate will probably cut more out to make room for a/c condenser, oil cooler, intercooler, and rad, Any one ever seen a 510 with radiator in trunk? im considering it. Pic ture of valves is as so: left stock, middle and right mismatching intake valves from supertech, 2 match, and 6 match. I have other ideas for wider body as well will post soon!
  9. hahah so is the driver one back wards or the passenger one?
  10. i bought a roadster about a year ago and the speedo cable adapter that bolts to the tranny broke and while i was taking care of that i was paying attention to how the sway bar mounts because i dont have one on. I then noticed that the lower a arm seems to be ass backwards on one side heres pics. I know the driver's side one is correct as its the side that is shown in the fsm. They were taken from the front of the car. DRIVER Notice straight of arm is in rear, also slit on bottom of arm is in rear here---------------------^ PASSENGER on this side the bend of the a arm is in the rear and the straight is in the front along with the slit being in the front. any feed back would be great thank you and i think the lower arm could just be flipped if it is incorrect as it may be as the previous owner who did the painting assembled it.
  11. i got one shits smoother than the one in my car 200 anyone?
  12. HALF off make me any offer i have a complete car so theres stuff not listed above.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.