Jump to content

Can't seem to get Pertronix to fit new distributor


RIVRON

Recommended Posts

Have a new in the box Datsun part no 22100-U6001 distributor but I can't get the pertronix magnet ring to slide down far enough on the distributor lobe shaft and there is no hole in the housing the right size  for the wire grommet.  I see no way to do it.  I don;t remember where I got the distributor and may be incorrect.  Any info or a source for new Hitachi would be appreciated.

Link to comment
  • Replies 8
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Have a new in the box Datsun part no 22100-U6001 distributor but I can't get the pertronix magnet ring to slide down far enough on the distributor lobe shaft and there is no hole in the housing the right size  for the wire grommet.  I see no way to do it.  I don;t remember where I got the distributor and may be incorrect.  Any info or a source for new Hitachi would be appreciated.

Pictures of the guts please...

Link to comment

this distributor have a matching mount? willit mount to a L16 510? you have to many varibles that we are guessing.

If magnet ring prevents the Pertr Mag ring to go on the point lobe it most like a L20b dist. Which can work if one machines the ring FLUSH to the dist shaft..

 

send photo. of what exactly you have going from and going to NEWER set up. L16 dist mounts don't fit the L20b dist set up unless you get the correct set up.

 

 

L16 single point 68-69

I had a Mitshbishi dist and also L20b dist fit the Pertronix

 

 

Pertronix is a point conversionjust use the stock coil and ballast as what you have.

  • Like 2
Link to comment

 

Dual points were fazed out in late '73

 

The L18 610 had the 22100-U6001 single points to the end of July '73. The L20B was used from Aug '73 on also with single points 22100-U6001 distributor. The '74 model year 610 is the earliest use of the L20B by Nissan

 

The L18 710 used the single points 22100-U6001 distributor through '74. Then switched to L20B with single points

 

The L16 620 used a dual points distributor through Sept '73 switching to an L18 22100-U6001 single points distributor till Aug '74. Then switching to an L20B with single points

 

 

 

 

Link to comment

this distributor have a matching mount? willit mount to a L16 510? you have to many varibles that we are guessing.

If magnet ring prevents the Pertr Mag ring to go on the point lobe it most like a L20b dist. Which can work if one machines the ring FLUSH to the dist shaft..

 

 

 

 

Ring red arrow ,,,, needs to be machined down to shaft (blue) arrow for pickup to go all the way down.  OR just small enough to fit the Pertronix ring on,  I can't remember if there is a tiny step,, measure inside diameter of Pertronix ring to make sure

   a  neighborhood garage/grandpa  machinist might do it for as little as $20.  These are  soft metal and very easy setup in lathe

 

I have seen people use a drill press and a sharp metal file if you are brave enough... Or cheap enough,,  :rofl:  it just takes quite awhile 

 

 

ii80vC1.jpg?2

 

 

.

  • Like 2
Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.