Javi_Mayne Posted February 3, 2015 Report Share Posted February 3, 2015 Ok guys I'm a 17 year old with a 1981 Datsun 210 and have stock wheels which are 13"s. Is there any way I can fit a bigger rim? I've been looking for a while and finally saw some rims I like but they are 15x8. What would you guys recommend? Thanks in advanced! Quote Link to comment
flatcat19 Posted February 3, 2015 Report Share Posted February 3, 2015 15x7s with low/negative offset is what I recommend. Make the wheels fit the car, not the car fit the wheels. Quote Link to comment
tr8er Posted February 3, 2015 Report Share Posted February 3, 2015 22x3 wagon wheel styly. That, and listen to flat. I'd trust him 1 Quote Link to comment
flatcat19 Posted February 3, 2015 Report Share Posted February 3, 2015 Notice...been a member for 2 months, has 3 posts. His 3 posts were all threads he started. 1 asking for a sticker. 1 asking about 14" wheels and this one, asking for 15" wheel fitment. Any wagers on his next thread? Quote Link to comment
tr8er Posted February 3, 2015 Report Share Posted February 3, 2015 Oh oh me me me. Quote Link to comment
TENDRIL Posted February 3, 2015 Report Share Posted February 3, 2015 Member title? Quote Link to comment
flatcat19 Posted February 3, 2015 Report Share Posted February 3, 2015 I was thinking 5 speed. But it is a 210...so coilovers, maybe? Quote Link to comment
tr8er Posted February 3, 2015 Report Share Posted February 3, 2015 Bigger sticker? Quote Link to comment
Fat510 Posted February 3, 2015 Report Share Posted February 3, 2015 "how do i lower my 210?" Quote Link to comment
flatcat19 Posted February 3, 2015 Report Share Posted February 3, 2015 "how do i lower my 210?" What coilovers for the rear? Quote Link to comment
DaBlist Posted February 4, 2015 Report Share Posted February 4, 2015 what motor mounts do I need for a 2JZGTE swap 1 Quote Link to comment
Dolomite Posted February 4, 2015 Report Share Posted February 4, 2015 what motor mounts do I need for a 2JZGTE swap I'm thinking rb26det ''bolt in kit'' 1 Quote Link to comment
flatcat19 Posted February 4, 2015 Report Share Posted February 4, 2015 I'm thinking rb26det ''bolt in kit'' I know it exists. I saw a set of JDM mounts on eBay-made by CX Racing, I think. 1 Quote Link to comment
Seansm10 Posted February 4, 2015 Report Share Posted February 4, 2015 Javi the best you can do is find an online calculator for width and sidewall size to find the OD and take a tape measure to your fender wells and see what fits. Then measure both ways from the hub to see if the width and offset will be accepted by the fenderwells. You can also check rimtuck.com , your exact vehicle might not be in there but you can look at similar trucks and find a look you like/want to go for and all the wheel specs are supplied, as well as suspension mods to make said setup work. Good luck 2 Quote Link to comment
Guest Rick-rat Posted February 5, 2015 Report Share Posted February 5, 2015 With a big fucking hammer and a saw-all, anything you want will fit 1 Quote Link to comment
thatdirtykid Posted February 28, 2015 Report Share Posted February 28, 2015 Best wheel and tire calculator. http://www.rimsntires.com/specspro.jsp Also google this forum, lots of info here. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.