Busta Nut Posted April 4, 2014 Report Share Posted April 4, 2014 I'll add mine if you guys don't mind..... http://community.ratsun.net/topic/40947-project-5teeezya-pharaohs-510/page-15 It's holding up great so far....... 1 Quote Link to comment
Droze Posted March 8, 2015 Report Share Posted March 8, 2015 Your post is a lifesaver Creepy Cruiser! As i was dropping the tank on my '72 last night every piece of rubber just crumbled in my hand...needless to say i will be trying your method this week. Thank you for this post! 1 Quote Link to comment
datsunfreak Posted March 9, 2015 Report Share Posted March 9, 2015 The only issue is when I pull the nozzle out, the last few drips always get on the paint due to the tilt (or lack of) but thats with all my cars. Just a couple shakes and it solves that issue My wife's car (2013 model) has a sticker on the gas door that says "wait 5 seconds before removing nozzle". Oddly enough, this works every single time. ^_^ Quote Link to comment
Creepy Cruiser Posted March 10, 2015 Author Report Share Posted March 10, 2015 Your post is a lifesaver Creepy Cruiser! As i was dropping the tank on my '72 last night every piece of rubber just crumbled in my hand...needless to say i will be trying your method this week. Thank you for this post! No problem. Glad I could help. (that's what this community is all about, helping each other out) 3 Quote Link to comment
bananahamuck Posted March 20, 2015 Report Share Posted March 20, 2015 So i can hardly see the back side of full install but from what i see laying here ( 4 holes in my Mazda unit) i assume you re-drilled or used self taping screws to match the holes already in car and plate that was cut down from OG inlet?? Quote Link to comment
Creepy Cruiser Posted March 20, 2015 Author Report Share Posted March 20, 2015 Correct. I used self-tappers to do the original mockup, and then I removed them one at a time and replaced them with nice flat allen headed bolts. 1 Quote Link to comment
Ctrack Posted April 28, 2015 Report Share Posted April 28, 2015 thanks for the tip! Quote Link to comment
That4doorKiD Posted August 20, 2015 Report Share Posted August 20, 2015 Nice! and THX did this tutorial :thumbup: Quote Link to comment
qwik510 Posted August 20, 2015 Report Share Posted August 20, 2015 ^^^ Those Injen couplings look like they are from an air intake system. Do you know if they are fuel safe? Quote Link to comment
That4doorKiD Posted August 21, 2015 Report Share Posted August 21, 2015 Yeah, they're silicone, from air intake, just temporary till I can find fuel grade Quote Link to comment
qwik510 Posted August 21, 2015 Report Share Posted August 21, 2015 Yeah, they're silicone, from air intake, just temporary till I can find fuel grade Ok cool. As long as it's temporary. 1 Quote Link to comment
cl72wagon Posted November 20, 2015 Report Share Posted November 20, 2015 Here is what I did. I used most of the parts and tools Creepy used. Thanks Creepy Cruiser for how to. http://community.ratsun.net/topic/68031-another-fuel-filler-neck-replacement-for-a-510/?do=findComment&comment=1320036 Quote Link to comment
updog Posted February 9, 2017 Report Share Posted February 9, 2017 Other than an Isuzu Pup what is another compatible filler neck hose I can use that has the proper bend in it? I can't find one. Thanks in advance. Quote Link to comment
Draker Posted February 9, 2017 Report Share Posted February 9, 2017 I can't remember what I pulled mine from.. might have been a Mazda or a Dodge something around the same year. Quote Link to comment
bananahamuck Posted February 9, 2017 Report Share Posted February 9, 2017 Click on the link in the post just above your question. 1 Quote Link to comment
nvestor88 Posted June 20, 2017 Report Share Posted June 20, 2017 Where can the Mazda b2200 filler neck be found? Quote Link to comment
Creepy Cruiser Posted June 23, 2017 Author Report Share Posted June 23, 2017 Time for an Update: It's still leak and smell free since I did it. I love it. Where can the Mazda b2200 filler neck be found? Most self serve wrecking yards have a few Mazda PU in them. (depending on your area I guess) 1 Quote Link to comment
freekwonder Posted June 23, 2017 Report Share Posted June 23, 2017 Yup, haven't had an issues myself either since I've done this. Nice not having fuel on the side of the my. My only problem isn't related to the filler neck. Can't fill my tank up too much or fuel seeps out of the welds where the fuel pump was welded in at. Need to take it out and reseal the tank. 1 Quote Link to comment
toylet Posted May 28, 2023 Report Share Posted May 28, 2023 (edited) Anyone doing this B2200 filler neck mod, you will need to use the Dorman 573076 fuel hose to connect fuel tank to filler neck. Perfect fit Edited June 15, 2023 by toylet . 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.