Jump to content


Photo
- - - - -

Replacement heater and intake by pass hoses 510


  • Please log in to reply
11 replies to this topic

#1 datzenmike

datzenmike

    KING RAT

  • User Administrator
  • 68,201 posts
  • Location:Vancouver Island
  • Cars:'74 710 sedan, '76 710. prevoius... '78 620, '71 521, '68 510 new '76 B-210

Posted 03 December 2012 - 06:35 PM

These are substitutes for the OEM molded hoses that are hard to find, expensive or non existing. They may fit 610/710s too or any application that needs a 90 degree molded heater hose.

This was posted by Byron on The 510 Realm so thank you Byron.

Single pass heater core alternative to OEM hoses for the interior side of heater assembly.

Dayco 86121 (2005 Kia Optima, 1989 Geo Spectrum, 1991 Chec Cavalier) can be utilized for both pieces – in fact you can make two sets out of the one hose!

Posted Image

Posted Image Posted Image Posted Image Posted Image Posted Image


Carburetor heat riser bypass hose alternatives to OEM, This is the line that runs from under the carb to the coolant inlet around the front of the motor when utilizing the stock OEM metal pipe.

Dayco 80394 (2004 Grand Vitarta, 1989 Honda Accord); Again this hose can be cut to fit both the 90 degree bend and the strait section required for installation of this bypass pipe.

Posted Image Posted Image

Posted Image Posted Image Posted Image Posted Image
Posted Image

#2 DanielC

DanielC

    Senior Member

  • Senior Member
  • PipPipPipPipPip
  • 4,502 posts
  • Location:West Linn,Or

Posted 03 December 2012 - 08:50 PM

If looks like the second hose would fit on a L-16 in a 521. The water inlet to intake manifold hose. The top hose may be useful in hooking up the heater on a 521, but i think some extra pieces would be needed.

#3 skyblue

skyblue

    Datsun Mechanic

  • Senior Member
  • PipPipPipPipPip
  • 4,663 posts
  • Location:East Bay, CA
  • Cars:1971 510 4dr, 1972 521, 1966 Impala, 1966 Yamaha Campus 60(YJ2), 1973 240z, 2003 SV650

Posted 03 December 2012 - 10:28 PM

wow tha'ts a great alternative. thx for sharing.

#4 banzai510(hainz)

banzai510(hainz)

    L motor God

  • Senior Member
  • PipPipPipPipPipPipPipPipPipPip
  • 14,868 posts

Posted 04 December 2012 - 06:30 AM

521 the metal from heater ,line is smaller I believe than the 510 one.

this should be posted on olddatsuns.com also parts swap or something

510 hoses are still avail but the 521s are harder to find now I think.
Throw on some Weber sidedrafts, Rising Sun hood.... call it good

#5 datzenmike

datzenmike

    KING RAT

  • User Administrator
  • 68,201 posts
  • Location:Vancouver Island
  • Cars:'74 710 sedan, '76 710. prevoius... '78 620, '71 521, '68 510 new '76 B-210

Posted 04 December 2012 - 07:11 AM

wow tha'ts a great alternative. thx for sharing.



Well Byron posted it on of The 510 Realm I just brought it here.
Posted Image

#6 Ryan Family 510

Ryan Family 510

    Senior Member

  • Senior Member
  • PipPipPipPip
  • 383 posts
  • Location:Redlands Ca
  • Cars:1969 510

Posted 22 January 2015 - 02:55 PM

Very helpful, thank you

#7 Humboldt

Humboldt

    Advanced Member

  • Members
  • PipPipPip
  • 101 posts
  • Location:Northern California
  • Cars:1980 720, 1972 510 Wagon work in progress

Posted 10 June 2016 - 04:48 PM

Somewhat on topic . . . does anyone have a source for Water Inlet Gasket for L16? I have searched all over. Thanks



#8 DanielC

DanielC

    Senior Member

  • Senior Member
  • PipPipPipPipPip
  • 4,502 posts
  • Location:West Linn,Or

Posted 10 June 2016 - 09:08 PM

Try your local Nissan dealer.



#9 Humboldt

Humboldt

    Advanced Member

  • Members
  • PipPipPip
  • 101 posts
  • Location:Northern California
  • Cars:1980 720, 1972 510 Wagon work in progress

Posted 11 June 2016 - 08:30 AM

Lame of me , but I presumed they wouldn't have it. I will check Monday, thanks.



#10 Humboldt

Humboldt

    Advanced Member

  • Members
  • PipPipPip
  • 101 posts
  • Location:Northern California
  • Cars:1980 720, 1972 510 Wagon work in progress

Posted 14 June 2016 - 09:11 PM

Thanks!

 

I ordered it and a couple xtras from Morlan Niisan in MO. Part number for Water Inlet Gasket: 13050-07N00 



#11 banzai510(hainz)

banzai510(hainz)

    L motor God

  • Senior Member
  • PipPipPipPipPipPipPipPipPipPip
  • 14,868 posts

Posted 14 June 2016 - 09:29 PM

Fepro front cover kits have them also. I usually don't remove those from the front cover


Throw on some Weber sidedrafts, Rising Sun hood.... call it good

#12 datzenmike

datzenmike

    KING RAT

  • User Administrator
  • 68,201 posts
  • Location:Vancouver Island
  • Cars:'74 710 sedan, '76 710. prevoius... '78 620, '71 521, '68 510 new '76 B-210

Posted 15 June 2016 - 02:23 PM

Somewhat on topic . . . does anyone have a source for Water Inlet Gasket for L16? I have searched all over. Thanks

 

Make your own!!!

 

Go to dollar store and buy a round hole punch, borrow kitchen scissors. Trace out gasket on cereal box. Hole punch the bolt holes. Hole punch the larger opening so you can finish with scissors and you are done. Do NOT use rtv just put it on and forget it. Use anti-seize compound on the bolts. I have cereal box thermostat cover and mount gaskets on my 710 right now and I'm about 1,500 miles into my travels. I never worry about gaskets.


Posted Image