BenTerrible Posted November 7, 2012 Report Share Posted November 7, 2012 Bought a factory console and received it in the mail today. My car is a 1970 4 door, manual. I was told this would fit. Tried to install and the shifter will not line up with the console at all. The console is all the way up against the heater box that is under the dash but this thing is nowhere close to falling into place. I have noticed that some 510's have the oval shifter hole in the floor while others are round. Mine is the oval. Any help? Thanks, Quote Link to comment
ggzilla Posted November 7, 2012 Report Share Posted November 7, 2012 Photo looks like a 510. That console looks similar to the Datsun dealer accessory from AMCO. Quote Link to comment
Guest 510kamikazifreak Posted November 7, 2012 Report Share Posted November 7, 2012 At the heater box end of the console,there is a recess in the console for it to tuck under the heater, have you done this?(hard to tell from pic) Quote Link to comment
BenTerrible Posted November 7, 2012 Author Report Share Posted November 7, 2012 Yes, that recess is tucked under the heater. Quote Link to comment
Guest 510kamikazifreak Posted November 7, 2012 Report Share Posted November 7, 2012 Hmm, Is it a factory 4 speed or? Quote Link to comment
rayven14 Posted November 7, 2012 Report Share Posted November 7, 2012 Hmm your right... that doesnt fit :confused: Quote Link to comment
BenTerrible Posted November 7, 2012 Author Report Share Posted November 7, 2012 Yes, factory 4 speed, not an auto conversion. Quote Link to comment
Guest 510kamikazifreak Posted November 7, 2012 Report Share Posted November 7, 2012 Have a better pic of it ?(top view) It should fit if it is a factory 4 speed etc. Quote Link to comment
I'm BLUE Posted November 7, 2012 Report Share Posted November 7, 2012 Do you have double-layer insulation , carpet padding , thick carpet ? Quote Link to comment
Guest 510kamikazifreak Posted November 7, 2012 Report Share Posted November 7, 2012 Do you have double-layer insulation , carpet padding , thick carpet ? I dont think the console would slide under the heater, if it were double insulated/thicker carpet Quote Link to comment
I'm BLUE Posted November 7, 2012 Report Share Posted November 7, 2012 I dont think the console would slide under the heater, if it were double insulated/thicker carpet more of pointing in the right direction/brain-storm on my end :D you guys are the 510 experts not me .. :lol: I have no real clue what's going on haha ! DTP OUT !!! *Farts and Scoot's away* Quote Link to comment
danfiveten Posted November 7, 2012 Report Share Posted November 7, 2012 Sigh. Whoever had that cut the hole in a different place. If you did not get it as a car option. they came un-cut, so whoever cut it must of had a longer transmission due to a different motor. Or your car has a different transmission. Ill take a pic of mine to show you where it should be cutted at, or the area yours is needing. Quote Link to comment
Guest 510kamikazifreak Posted November 7, 2012 Report Share Posted November 7, 2012 DTP OUT !!! *Farts and Scoot's away* :rofl: Quote Link to comment
Guest 510kamikazifreak Posted November 7, 2012 Report Share Posted November 7, 2012 Sigh. Whoever had that cut the hole in a different place. If you did not get it as a car option. they came un-cut, so whoever cut it must of had a longer transmission due to a different motor. Or your car has a different transmission. Ill take a pic of mine to show you where it should be cutted at, or the area yours is needing. I am thinking the same thing,maybe someone picked up a nos one(uncut) at some point,and cut it for a zx 5spd Quote Link to comment
danfiveten Posted November 7, 2012 Report Share Posted November 7, 2012 PICS Ours are cut in WAY different locations. My suggestion is cut it up higher, then save that plastic, see if you can find a big enough shift boot to cover that entire hole. If not take the left over plastic you cut, shape it to same size as the left over hole, find a plastic welder, flip it over, and have it done up to fit. U will notice a lil difference in looks but looks better than a giant hole. Yours is cut right abouv the datsun logo is supposed to go. the shift layout plate should be where yours is cut at. Quote Link to comment
BenTerrible Posted November 7, 2012 Author Report Share Posted November 7, 2012 PICS Ours are cut in WAY different locations. My suggestion is cut it up higher, then save that plastic, see if you can find a big enough shift boot to cover that entire hole. If not take the left over plastic you cut, shape it to same size as the left over hole, find a plastic welder, flip it over, and have it done up to fit. U will notice a lil difference in looks but looks better than a giant hole. Yours is cut right abouv the datsun logo is supposed to go. the shift layout plate should be where yours is cut at. THANKS! This explanation makes total sense now. I was unaware that these came uncut! I know for a fact my car is 100% original as far as motor/trans and it being a manual. The hole in my console is cut much closer to the arm rest compared to the one in the photo you posted. No I need to figure what I am going to do with this thing?!?! Quote Link to comment
ggzilla Posted November 7, 2012 Report Share Posted November 7, 2012 Cut a new hole, and make a coin pocket in the old hole. Quote Link to comment
BenTerrible Posted November 7, 2012 Author Report Share Posted November 7, 2012 Cut a new hole, and make a coin pocket in the old hole. ...genius. Quote Link to comment
danfiveten Posted November 7, 2012 Report Share Posted November 7, 2012 Or get one of those cup holder things at the auto store, cut a new hole for shifter, then re cut the back after you put a shift boot in to fit one of those cup holder thingies ;) Quote Link to comment
yenpit Posted November 20, 2012 Report Share Posted November 20, 2012 I made a panel that sat down in the long "cavity" to cover the old shifter hole. In other words, cut a panel out of masonite (just like the door panels & kick panels, available at any Lowes, Home Depot etc) to fit the full length of that dropped down cavity, wrapped it in black vinyl, cut a new hole that matched the location of your shifter (4spd, ZX 5spd etc), came up with a nice shifter boot, and made sure that the console itself was secured to the trans tunnel (that's another story, cuz those flimsy dealer optional AMCO consoles were made out of stupid thin moulding injected plastic, that easily broke at the screw holes over time!). Quote Link to comment
Droze Posted March 10, 2015 Report Share Posted March 10, 2015 I know this post is old so sorry for bumping it back up, but really hoping someone has a good pic of the shift layout plate...i have the plate on my '72 2dr. but it needs a mild reconditioning and i haven't been able to find a clean pic of how it looked from factory. Any help would be stellar! Since my console is old and almost ready to fall apart I'm going to make a fiberglass mold and make a new one off the old factory one ...at least i can paint match that to whatever i choose for interior color Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.