Jump to content
  1. General

    1. General Discussion

      Talk about anything.

      537.9k
      posts
    2. Events

      Upcoming events.

      89.3k
      posts
    3. Project Datto

      A place to discuss Datsun projects.

      215k
      posts
    4. Datsun Stories

      Share a Datsun story.

      10.5k
      posts
  2. Datsun Discussion

    1. Cars

      A place to talk about Datsun cars.

      153.8k
      posts
    2. Trucks

      Talk about your Datsun truck.

      284.2k
      posts
    3. Other Datsuns and Nissans

      A place for all other Datsun and Nissan vehicles which don't fall into the main forums.

      15.6k
      posts
  3. Technical

    1. General Technical

      A place to discuss technical aspects which aren't necessarily covered in a specific forum.

      26.2k
      posts
    2. Engine

      If you don't know what this is, you probably shouldn't work on a car (or drive it even).

      85k
      posts
    3. Drivetrain

      This stuff makes your wheels turn.

      22.2k
      posts
    4. Suspension

      Springy sort of stuff.

      15.7k
      posts
    5. Electrical

      Wires and such.

      24.3k
      posts
    6. Brakes

      These things make your car stop!

      10.2k
      posts
    7. 17.1k
      posts
    8. Wheels and Tires

      Round. Rubber.

      10.1k
      posts
  4. Write Ups

    1. How-To

      Submit a "HowTo" write-up.

      8.2k
      posts
  5. Classifieds

    1. Classified Ads   (318,546 visits to this link)

      Redirect to the classified advertisements.

    2. Discussion

      Discussion about classified ads.

      1.8k
      posts
    3. 164.4k
      posts
  6. Off Topic

    1. Non Datsun Cars and Projects

      Discuss your Non-Datsun cars and projects.

      24.3k
      posts
  • Upcoming Events

    No upcoming events found
  • Posts

    • We have been documenting our efforts on the race car thread. This one might be a way to summarize our efforts in the future.  Skip to the end if you want Honda motor content.    
    • More amateur gunsmithery happened! New Wilson Combat trigger fitted, went smooth as butter. New extended slide release fitted, that was a colossal cock-up that took an hour of filing and fiddling and filing and fiddling to make it work smooth, but now it does.       So for anyone keeping track, Wilson Combat parts do indeed actually just drop right in. Everything else, doesn't.  😄
    • Being a 6000ft it could probably use a little adjustment but having 1 plug foul not all 4 seems suspect..... You'd think if you air fuel was off it would effect all cylinders.....   The only thing the comes to mind are counterfeit plugs from Amazon or ebay....    Where did you get the plugs ?
    • I'm having a similar problem with my Nikki Carb on my Datsun 520 pickup. My original fuel pump is working, and it appears I'm getting fuel into the bowl, but no start except with starter fluid or pouring a little gas in the carb. I took the needle valve assembly off and the little spring, plunger and needle all just fell out. Is it suppose to be loose like that and just rest on top of the float adjustment? I suppose I need to look at the float level since ya'll said that "the float gets stuck on it if it goes all the way to the bottom". That could be, I suppose, what's stopping gas from going any further into the carb. I don't have a clear cover, so I can't see the fuel level. My main concern is that the needle valve, spring and plunger only seem to be supported by the float, and there's nothing else to hold them into the needle valve assembly. Is that the way it's suppose to be? it makes for tedious work if you're trying to put it back in with the carb already installed!
    • Hi guys I've done reading on as many sights as possible but I cant quite seem to find exactly what it is im looking for  I have a distributor from a 1984 z24 And im looking to mount it onto my z24i because im going turbo and fitech. All I want to know is what else do I need to make it all fit together from what it looks like ill need to swap to a different timing cover to make the mounting correct also the distributor doesn't seem to seal at all with my current timing cover so if anyone has any info on this topic a response would be very much appreciated thank you so much. 
  • Recent Status Updates

  • Adverts

  • Member Statistics

    • Total Members
      49,136
    • Most Online
      2,169

    Newest Member
    Wopsa Web Services
    Joined
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.